BRHSLIST
[Top] [All Lists]

RE: [CBQ] CB&Q Facilities, Vol. 2 Questions

To: CB&Q Group <cbq@yahoogroups.com>
Subject: RE: [CBQ] CB&Q Facilities, Vol. 2 Questions
From: "Hol Wagner holpennywagner@msn.com [CBQ]" <CBQ@yahoogroups.com>
Date: Mon, 15 Jun 2015 14:25:20 -0600
Delivered-to: unknown
Delivered-to: archives@nauer.org
Delivered-to: mailing list CBQ@yahoogroups.com
Dkim-signature: v=1; a=rsa-sha256; c=relaxed/relaxed; d=yahoogroups.com; s=echoe; t=1434399923; bh=eJa+lC2rY8pAXLAl0WFu0H1eCRCGhonEvAZg6R+7hUE=; h=To:In-Reply-To:References:From:List-Id:List-Unsubscribe:Date:Subject:Reply-To:From:Subject; b=30D1FjhshHmE/bw1oWGU0QkFD8cqc09fcwNS/rAEp+LIaQLE6KjjgVrDBvu5s77Qkzyapc4kw1J0fXz/JlRqSP1U4MWHVRnjjZ7YJZ2Gxa7IzrRMW6KulmAkFuVd5Xq4SafDKHtKKhCjB9KLjeoMgzsfglcVJqLV3U6wAKA1D00=
Importance: Normal
In-reply-to: <BE880F7C-A9D8-4796-9C07-4EEB54991A0A@aol.com>
List-id: <CBQ.yahoogroups.com>
List-unsubscribe: <mailto:CBQ-unsubscribe@yahoogroups.com>
Mailing-list: list CBQ@yahoogroups.com; contact CBQ-owner@yahoogroups.com
References: <qi9m44wbgs6j8jrds3pi3ib8.1434394929330@email.android.com>,<BE880F7C-A9D8-4796-9C07-4EEB54991A0A@aol.com>
Reply-to: CBQ@yahoogroups.com
Sender: CBQ@yahoogroups.com


In earlier years, slag was also a waste product of the precious metals refining process, and smelters produced great volumes of slag that were also used as ballast by railroads, the C&S being one of the primary users -- and also using steel mill slag from the CF&I mill at Pueblo.
 
Hol
 

To: CBQ@yahoogroups.com
From: CBQ@yahoogroups.com
Date: Mon, 15 Jun 2015 14:46:52 -0500
Subject: Re: [CBQ] CB&Q Facilities, Vol. 2 Questions

 
Nelson,

B & B stood for bridge and building. These crews maintained things. There were paint gangs,bridge gangs,etc. By other crafts B&B was often credited with making jobs last a long time. On the other hand RR facilities did hold up under some pretty tough use(Abuse).

Slag is one of the waste products from making steel. It's nonmetallic and comes from the molten lime coke,etc. it's poured in pits at the mills and when cooled sold off. It was widely used on lines east for mainline ballast. It was cheap to purchase and provided good water run off,even if it was harder than heXX to walk on.  A large accumulation would be gathered at Eola in the slag hole and then used in the various projects.

Leo Phillipp

On Jun 15, 2015, at 2:02 PM, tf5077 tf5077@yahoo.com [CBQ] <CBQ@yahoogroups.com> wrote:

 

Bridges and Buildings........ I believe

"'Nelson Moyer' ku0a@mchsi.com [CBQ]" <CBQ@yahoogroups.com> wrote:

 


I just finished reading the subject book, and there are two references to B&B that seem to be related to maintenance of way. What does B&B stand for in Q terminology?

 

The alignment charts are a welcome addition, and I hope they will continue for Vol. 3, etc. Of particular interest to modelers is the rail weight and ballast used on various parts of the railroad at specified dates. Apparently, the Q used whatever was available for ballast. I found CR Rock (presumable crushed rock, but it would be nice to know what rock was used), slag, gravel, cinders, and slag-mannix listed. What is mannix? As I understand it, slag was the waste material from coal mining that was stacked up in gob piles in Southern Illinois and subsequently used as ballast.

 

Photos in the volume 1 and 2 show a v ariety of ballast types, some overlaying cinder subroadbed. Yard ties apparently had sunk in mud, since they were flush with the dirt level and showed some cinder residual and very little ballast. All this is very helpful to modelers wishing to reproduce the authentic appearance of yards and other trackage.

 

The one structure that has not yet been shown in either book is an ash pit. I’m at the stage on my layout where I need to build and install an ash pit, and I have very little Q specific information on ash pits in general and no information about an ash pit in the Burlington, IA service facility. Drawings and photographs would be very helpful.

 

Nelson Moyer



Posted by: "Nelson Moyer" <ku0a@mchsi.com>
Reply via web post Reply to sender Reply to group Start a New Topic Messages in this topic (1)
!



__._,_.___

Posted by: Hol Wagner <holpennywagner@msn.com>



__,_._,___
<Prev in Thread] Current Thread [Next in Thread>