BRHSLIST
[Top] [All Lists]

[CBQ] RE: [STMFC] CB&Q 48 foot composite mill gons

To: <STMFC@yahoogroups.com>, <CBQ@yahoogroups.com>
Subject: [CBQ] RE: [STMFC] CB&Q 48 foot composite mill gons
From: "Charlie Vlk" <cvlk@comcast.net>
Date: Thu, 6 Sep 2012 13:35:41 -0500
Delivered-to: unknown
Delivered-to: archives@nauer.org
Delivered-to: mailing list CBQ@yahoogroups.com
Dkim-signature: v=1; a=rsa-sha256; c=relaxed/relaxed; d=yahoogroups.com; s=lima; t=1346956548; bh=ol+vDyPTwItqQ+7aA2Viy78ToTsjkX9MpMC0PI/z+j4=; h=Received:Received:X-Yahoo-Newman-Id:X-Sender:X-Apparently-To:X-Received:X-Received:X-Received:X-Received:X-Received:To:References:In-Reply-To:Message-ID:X-Mailer:Thread-Index:Content-Language:X-Originating-IP:X-eGroups-Msg-Info:From:X-Yahoo-Profile:Sender:MIME-Version:Mailing-List:Delivered-To:List-Id:Precedence:List-Unsubscribe:Date:Subject:Reply-To:X-Yahoo-Newman-Property:Content-Type; b=MUYlCkKBszLRF7o+ey+foK+M4eU88U3eXLqcivO2ba8BReaDS7m4mYwx3mKWlgIWE8tncTdzSO/BqZRDjU6t4kCrGLU1wsGSCFa598RJXxpFS776KYYCklmL+hsAfGZ4
Domainkey-signature: a=rsa-sha1; q=dns; c=nofws; s=lima; d=yahoogroups.com; b=nDVp/HrvAFR6Z5JLSbkBYEha+pA6fJysM7rCXM1lQALgZK56e7M6IXYfamNS2FK1nsOGP0P08KsMesekjgkMLU6ny1HNGre2Eys2L+8Ry2Ca/V0c495xh2/4al9MQ5H2;
In-reply-to: <8CFDC8568ABD41F09832220A0E6B26AE@CPU2011>
List-id: <CBQ.yahoogroups.com>
List-unsubscribe: <mailto:CBQ-unsubscribe@yahoogroups.com>
Mailing-list: list CBQ@yahoogroups.com; contact CBQ-owner@yahoogroups.com
References: <8CFDC8568ABD41F09832220A0E6B26AE@CPU2011>
Reply-to: CBQ@yahoogroups.com
Sender: CBQ@yahoogroups.com
Thread-index: Ac2L4LWkHG8rZpJTQXO8fFgtXzC4pgAfOJ/g


 

Klaus-

I didn’t notice this before but the end panels on the prototype is not symmetrical….it appears that one end of the car is shorter (in relation to the body bolster) than the other.  The strap diagonal on the long end is at the same angle as the pressed steel truss members, but on one end the panel is shorter and the strap diagonal is consequently at a sharper angle.

This shows up on the builders photo and in-service cars but not the Kalmbach MR Cyclopedia drawing.  I wonder if this was done for clearance on the brake gear and platform?
Weird.

Charlie Vlk



__._,_.___


Your email settings: Individual Email|Traditional
Change settings via the Web (Yahoo! ID required)
Change settings via email: Switch delivery to Daily Digest | Switch to Fully Featured
Visit Your Group | Yahoo! Groups Terms of Use | Unsubscribe

__,_._,___
<Prev in Thread] Current Thread [Next in Thread>